PTCL Fiber Signal Strength (dBm) Checker

Signal strength checker

Type the number from your router's status page. Fiber is checked against GPON class B+ optics, the type PTCL Flash Fiber and most FTTH networks in Pakistan use.

How to use the signal strength checker

  1. Open your router page. For PTCL routers type 192.168.10.1 in the browser while connected to its WiFi and log in.
  2. Find the optical information (fiber), the WiFi signal (phone or laptop), or the DSL line statistics (copper). The paths for common routers are listed below.
  3. Pick the matching tab above and type the number, including the minus sign for dBm values.
  4. The marker on the colour bar and the verdict show whether the signal is good, weak or failing, with what to do next.

Fiber optic power ranges (GPON)

Fiber-to-the-home in Pakistan, including PTCL Flash Fiber, Nayatel, StormFiber's FTTH areas and most housing-society fiber, runs on GPON (Gigabit Passive Optical Network). The router at your home is called an ONT (Optical Network Terminal) or ONU. The light reaching it, the Rx (receive) power, is measured in dBm.

Rx powerRatingWhat happens
-8 dBm or higherToo strongRare; can overload the receiver
-8 to -24 dBmGoodStable connection with healthy margin
-25 to -27 dBmWeakWorks, but sensitive to dirt, bends and weather
-28 dBm or lowerFailingDrops, slow speeds, LOS light red

Class B+ GPON optics are specified to work down to about -28 dBm, and most ISPs aim to install new connections at -15 to -24 dBm so the link stays healthy as connectors age. The Tx (transmit) power from your ONT is normally between +0.5 and +5 dBm; a value far outside this points to a faulty router optic.

Why the numbers are negative

dBm is power relative to one milliwatt (mW). 0 dBm = 1 mW, -10 dBm = 0.1 mW, -20 dBm = 0.01 mW and -30 dBm = 0.001 mW. Every 3 dB is double or half the power. So a reading of -27 dBm carries half the light of -24 dBm. Closer to zero means stronger.

Where to find fiber Rx power on your router

RouterMenu path (may vary by firmware)
Huawei HG8245H / HG8145V5 / EG8145Status → Optical Information
ZTE F660 / F670L / F680Status → Network Interface → PON Information (or Network → PON → Optical Module)
Fiberhome AN5506 / HG6243CStatus → Optical Info (or Device Information → Optical Module)
Nokia G-140W / G-240WStatus → Optics Module Status

Some PTCL firmware hides this page from the normal user account. If you cannot see it, ask 1218 to read your optical power remotely; they can see it from their system.

Common causes of weak fiber signal

  • Dirty connectors. A speck of dust on the SC/APC connector can cost 1 to 3 dB. Technicians clean it with a one-click cleaner.
  • Tight bends. Indoor fiber should not be bent tighter than a coin. Cable clips, doors and furniture often pinch it.
  • Damaged drop cable on poles, walls or rooftops, especially after storms, construction or monkeys and birds chewing it.
  • Bad splices or extra splitters at the distribution box. Each splice and connector adds loss.

WiFi signal strength (RSSI)

RSSI is how strongly your phone or laptop hears the router, also in dBm. Typical values range from -30 dBm (next to the router) to -90 dBm (barely connected).

WiFi signalRatingGood for
-30 to -50 dBmExcellentEverything, full speed
-50 to -67 dBmGoodVideo calls, 4K streaming, gaming
-67 to -75 dBmFairBrowsing, WhatsApp; video may buffer
Below -75 dBmWeakDrops and very low speed

How to see it: on Windows run netsh wlan show interfaces in Command Prompt (it shows Signal as a percentage; roughly 100% ≈ -50 dBm, 50% ≈ -75 dBm). On Android, free WiFi analyser apps show dBm, and some phones show it under Settings → WiFi → network details. On a Mac, hold Option and click the WiFi icon. iPhones do not show dBm.

5 GHz WiFi is faster but weaker through walls; 2.4 GHz reaches further at lower speed. If you are two rooms away and the 5 GHz signal is below -70 dBm, the 2.4 GHz network may actually be faster.

DSL line statistics: SNR margin and attenuation

For PTCL DSL and VDSL on copper phone lines, the modem's status page shows SNR margin (how far the signal is above the noise) and line attenuation (how much signal is lost on the way, mostly due to distance from the exchange or cabinet).

SNR marginLine qualityAttenuationLine quality
Above 10 dBGood and stableUp to 20 dBExcellent (short line)
6 to 10 dBUsable, may drop at night20 to 40 dBGood to fair
Below 6 dBUnstable, frequent disconnectsAbove 50 dBPoor, low sync speed

Attenuation of 13 to 14 dB is roughly one kilometre of copper on ADSL, so it also tells you how far you are from the exchange. Unlike fiber, DSL speed falls steeply with distance; if attenuation is above 40 dB, check whether Flash Fiber is available in your area.

Frequently asked questions

What is a good fiber signal strength in dBm?

For GPON fiber (used by PTCL Flash Fiber and most FTTH in Pakistan), an Rx power between -8 and -24 dBm is good. -25 to -27 dBm still works but has little margin. Below -27 dBm the connection drops or the LOS light comes on.

Is -25 dBm good for fiber?

-25 dBm is acceptable but on the weak side. The connection will usually work, but dirt on the connector, a tight bend or bad weather on overhead cable can push it below the -27 to -28 dBm limit. Ask for the connectors to be cleaned and the drop cable checked if you see drops.

Why is fiber signal shown as a negative number?

dBm compares power with 1 milliwatt. 0 dBm is 1 mW, -10 dBm is 0.1 mW, -20 dBm is 0.01 mW. Fiber receivers work with tiny amounts of light, so normal readings are negative. A number closer to zero is a stronger signal.

What is a good WiFi signal strength?

Between -30 and -60 dBm is excellent to good. -67 dBm is the minimum for smooth video calls and streaming. Below -75 dBm you will see slow speeds and drops.

Fiber signal kitna hona chahiye?

Fiber router mein Rx power -8 se -24 dBm ke beech achi hai. -25 se -27 dBm par internet chalta hai lekin kamzor hai. -27 dBm se neeche internet band ho sakta hai aur LOS light jal sakti hai.

More free tools